Wenger Guitar Storage Rack Assembly Instructions Manual Download Page 1

Assembly Instructions

Guitar Storage Rack

©Wenger Corporation 2012

Printed in USA 10/12

Part #148J325-01

Wenger Corporation,

555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com

C

ONTENTS

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Manufacturer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Intended Use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Required Tools  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Fastener Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Secure an Instrument  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Replacement Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Note:

Please read and understand these instructions before assembling the parts.

Note:

Remove all items from the shipping cartons and arrange them in a convenient location. 

Refer to the illustrations on the following pages. 

If you need additional information, contact Wenger Corporation using the information below.

Note:

For easier assembly, two people are recommended.

Summary of Contents for Guitar Storage Rack

















Reviews: