4-SQUARE
FOR VARIFOCAL LENS:
TROUBLESHOOTING
ELECTRICAL BOX
RAFTER
Loosen the focal length and focus locking screws. Adjust according
ALL ADJUSTMENTS ARE MADE AT THE FACTORY FOR OPTIMAL
enclosure and mount
CEILING
to scene detail. Re-tighten the focal length and focus locking screws.
PERFORMANCE. THE FOLLOWING SETTINGS SHOULD ONLY BE USED IF
in a 4-square electrical
THESE ADJUSTMENTS DO NOT MEET THE REQUIREMENTS OF THE LOCATION
gang box in the ceiling
FLUSH DOME
FOR FIXED LENS:
CONDITIONS.
MOUNT
If the lens is out of focus, loosen lens set screw and turn clockwise
VERTICAL PHASE (LINE LOCK)
SOLID SURFACE
To synchronize multiple cameras and prevent vertical
mount chassis and
INSTALLING DOME & TRIM RING
roll, adjust the vertical phase (line-lock).
surface dome cover
CONDUIT
Be sure that all sealing washers are in place before mounting the trim
See following diagrams for location of potentiometer. Turn
in a 4-square electrical gang
and dome cover.
the potentiometer clockwise or counter-clockwise using a
box on a solid surface
FLUSH MOUNT
Place dome over mounting plate. The screw holes will self-align.
small screwdriver.
4-SQUARE
CHASSIS AND
The trim ring will "set" into place when holes are aligned.
ELECTRICAL
SURFACE DOME
Tighten the tamper-proof screws using the supplied L-Wrench.
AUTO IRIS LEVEL
BOX
COVER
(This L-Wrench is not standard design, keep it for further use)
Turn DC IRIS LEVEL control clockwise or counter-clockwise to adjust the
Pull the power and video wires into the 4-square electrical box or
light level. (FOR CAMERAS WITH AN AUTO-IRIS LENS) The location of the
in through the base of the surface mount enclosure. If necessary,
potentiometer is noted in the diagrams following.
attach conduit to the base of the enclosure and pull the wire in.
DIAGRAM
TOP VIEW
BACK LIGHT COMPENSATION
Mount the enclosure on a surface using the appropriate
1.
SELF ALIGNING SCREW HOLES (3)
Back light compensation (on) will allow the camera to filter out high gain background
hardware. Puncture the sealing washers with the mounting screws.
2.
MOUNTING HOLES FOR DOUBLE
(Do not remove the sealing washers from the mounting holes)
GANG BOX OR SURFACE MOUNT (8)
on the CCD board will provide adjustments for BLC (back light compensation).
If you are mounting directly to a wall or ceiling, it is recommended
3.
CAMERA MOUNT BASE AND
See following diagrams for the location of this switch.
that you use 1/4x20-inch hex-head bolts with wall anchors in high
PAN SCREWS
vandalism applications. If you are mounting to a 4-square electrical
4.
CAMERA MOUNT TILT SCREWS
CAMERA DIP SWITCH / POTENTIOMETER SETTINGS
gang box, use 4 each 8-32 screws.
5.
VARIFOCAL LENS LOCKING SCREWS
DSP COLOR
6.
SURFACE MOUNT TRIM RING AND
SURFACE MOUNT
WDDS - 2400S
CONNECT THE VIDEO AND POWER
DOME
WDDS - 2405S
Connect the video cable to the BNC connector.
7.
FLUSH MOUNT TRIM RING AND
FLUSH MOUNT
WDDF - 2400F
Depending on the power requirement of the camera (AC24V or DC12V),
DOME
WDDF - 2405F
connect the power wires to the appropriate input wires.
SIDE VIEW
CAUTION
BE SURE TO CONNECT THE CORRECT POLARITY TO
THE CORRECT WIRE INPUT ON CAMERAS REQUIRING DC12V.
6
7
LOCATED
ON BACK OF BOARD
ADJUSTING THE CAMERA AND LENS
Loosen the camera mount tilt screws. Loosen the camera mount
DC IRIS LENS LEVEL
pan and base screws.
LINE - LOCK (PHASE)
Adjust the camera to the proper pan position and tighten
down the camera mount pan and base screws.
SEE SPECIFICATION SHEET FOR FURTHER DETAILS ON PARTICULAR MODELS.
BLC MODE (ON / OFF)
Adjust the camera to the proper tilt position and tighten
ELECTRONIC IRIS (ON - AE / OFF - ME)
B
. Use the flush
or conterclockwise to focus.
C
. Use the flush
light to obtain forground details. Switches on the dip switch module located
2 1
3
4
2
3
4
5
ON
1 2