Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 86

Page: 86 / 148

1.5 About This Installation Manual

Purpose

The purpose of this installation manual is to provide everyone working with/on the combi oven with the

information they will need to transport, set up, install, and place the unit into operation safely and cor‐

rectly.

Target groups

This installation manual is intended for the following target groups:

Name of target group

Tasks

Mover

Transporting the unit within the facilities

Service technician

■

Setting up the unit

■

Installing and uninstalling the water connection

■

Installing the ConvoClean fully automatic cleaning system

■

Placing the unit into operation and removing it from service

■

Briefing the user

Electrician

Installing and uninstalling electrical connections

Installation manual outline

The following table describes the contents and goals for the various sections in this manual:

Contents

Purpose

General

■

Helps identify your combi oven

■

Explains how to use this installation manual

Configuration and Func‐

tions

■

Describes the combi oven's intended use

■

Explains the combi oven's functions and describes where its compo‐

nents are located

For Your Safety

Describes all the risks and hazards posed by the combi oven, as well

as appropriate instructions on how to prevent and/or counter them

Read this section carefully!

Transportation

■

Provides basic unit dimensions

■

Provides information on the requirements concerning the installation

location

■

Explains how to transport the unit to its installation location

Setup

■

Explains how to unpack the unit and goes over the included equip‐

ment and parts

■

Explains how to set up the combi oven

Installation

Explains how to install:

■

Electrical connection

■

Water connection

■

ConvoClean fully automatic cleaning system

Placing into operation

Explains how to put the unit into operation

Removing from Service,

Disposal

■

Explains how to remove the unit from service

■

Provides disposal information

Technical data

Contains technical specifications

Scale drawings and con‐

nection diagrams

Contains scale drawings and connection diagrams

1 General

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands