Weishaupt WWP LS 10-B R HE Installation And Operating Instruction Download Page 80

Page: 80 / 88

Installation and operating instruction
Hydraulic unit WWP LS 8 ... 16-B

10 Troubleshooting

83306902 2/2017-05 La

80-88

The following faults must only be rectified by qualified personnel:

Warning

Cause

Rectification

Power consumption of compressor motor too high

Normally no action is required. Troubleshooting
is only required, if the problem occurs several
times within one hour.

Check cooling circuit

Fan does not run

Check fan, if necessary replace

Compressor blocked

Check fan, if necessary replace

Impermissible operating condition

Briefly isolate the outdoor unit from voltage
supply
If the fault persists despite restart, check cir-
cuit board in outdoor unit and replace if ne-
cessary

Internal cooling sensor (B8) or heat exchanger pres-
sure sensor (B12) defective

Check the sensor and cable and replace if ne-
cessary

Condenser overheats

Normally no action is required. Troubleshooting
is only required, if the problem occurs several
times within one hour.

Check cooling circuit

Application limit exceeded

–

Insufficient flow

Minimum volumetric flow:

WWP LS 8: 0.8 m³/h
WWP LS 10: 1.0 m³/h
WWP LS 13: 1.2 m³/h
WWP LS 16: 1.3 m³/h

Check shut off device
Check thermostatic valves of heating circuit
Check flow sensor, if necessary replace

Flow/return spread of heating circuit to great

Increase volumetric flow
Increase pump capacity

Pressure at internal heat exchanger pressure
sensor (B12) to high.

Check the refrigerant level.
Check actuator of expansion vessel, replace if
necessary

No voltage supply to outdoor unit / blocked by en-
ergy generator

Wait for release by energy generator
Check voltage supply

50 / 51

External sensor (B1) defective

Check the sensor and cable and replace if ne-
cessary

52 / 53

De-couple sensor (B2) defective

54 / 55

DHW sensor (B3) defective

56 / 57

Flow sensor (B10) defective

Check cable, if necessary replace sensor

58 / 59

Flow sensor electric heating (B7) defective

Check the sensor and cable and replace if ne-
cessary

60 / 61

Internal refrigerant sensor (B8) defective

62 / 63

Return sensor EWT (B9) defective

64 / 65

Flow sensor (B10) defective

Check cable, if necessary replace sensor

66 / 67

Internal heat exchanger pressure sensor (B12) de-
fective

Flow sensor (B10) signal fault

Check cable, if necessary replace sensor

98 / 99

Internal fault

–

Summary of Contents for WWP LS 10-B R HE

























































































Search results

Summary of Contents for WWP LS 10-B R HE

Reviews:

Brands by name

Popular brands

Weishaupt WWP LS 10-B R HE, Installation And Operating Instruction

Search results

Summary of Contents for WWP LS 10-B R HE

Reviews:

Brands by name

Popular brands