manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Share
Download
Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 21

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

3 Product description

83309302 1/2018-05 La

21-196

WAS 80 Power/Bloc-P/A
WAS 115 Power/Bloc-P/B

The fresh water is heated via a plate heat exchanger.

DHW loading is initiated, when the temperature at the DHW sensor switch-on (B3)
drops below the DHW setpoint temperature minus the switch differential.

During DHW loading, the burner output is controlled via the DHW outlet sensor
(T1). DHW loading continues until the DHW sensor switch-off (T2) stops the load-
ing process.

1

2

3

w

q

0

9

8

7

6

5

4

1

Funnel siphon with outlet

2

DHW outlet sensor (T1)

3

Plate heat exchanger

4

Load pump stratified tank

5

DHW sensor switch-on (B3)

6

DHW sensor switch-off (T2)

7

Outlet tap

8

Fresh water inflow device

9

Inspection flange

0

Magnesium anode

q

DHW inflow damper

w

Non return valve

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands