Home
/
Weishaupt
/
WTC-GB 15-B Compact
/
Installation And Operating Instruction

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Share

Page: 121 / 196

Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 121

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

9 Servicing

83309302 1/2018-05 La

121-196

Prior to every servicing

Inform the operator about the extent of service work to be carried out.
Carry out input measurement [ch. 6.6.7.2].
Switch off mains switch of installation and safeguard against accidental reactiva-
tion.
Close fuel shut off devices.
Remove front panel of fresh water storage tank.
Remove front panel of condensing unit.

Service

Carry out servicing in accordance with the enclosed inspection card (Print No.
837569xx).

Following servicing

DANGER

Risk of electric shock

Touching the ignition device can lead to electric shock.

Do not touch ignition device during the ignition process.

Check soundness of gas valve train [ch. 7.1.1]
Check soundness of flue gas and condensate carrying components.
Check tightness of water carrying components.
Check soundness of burner cover / fan connection and burner cover / heat ex-
changer connection.
Mount the front panel of condensing unit and secure the tension lock with the
screw.
Fit front panel of fresh water storage tank.
Carry out flue gas measurement (calibration, O

2

correction), see [ch. 6.6.7.3].

Enter combustion values and settings in the commissioning record.
Resetting the service display [ch. 6.6.7].

9.1.2 Components

In addition to the servicing steps listed in the inspection card, the following com-
ponents must be tested for their design lifespan.

Components, which show increased wear and tear or whose design lifespan is or
will be exceeded prior to the next service should be replaced as a precaution.

Check the design lifespan of the components.
Replace components as necessary

Components

Design lifespan

WEM-FA-G device electronics

10 years or 360 000 burner starts

Gas combi valve

10 years or 500 000 burner starts

Gasket fan air outlet

10 years

Seal gas valve / fan

10 years

Burner gasket

10 years

Safety valve 3 bar

10 years

«
...
119
120
121
122
123
...
»

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands