Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 106

Page: 106 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

7 Commissioning

83309302 1/2018-05 La

106-196

3. Check device list

Select

and confirm.

Device list is loading.
The address of each Bus participant of the system is displayed in the device list.
Ensure all devices are shown.

Show device information:

Select relevant device.
Press dial knob.
The device selected flashes.
Press dial knob again.
Device information (

Software version

, etc.) is displayed.

If a device is not recognized, button can be used to reload the search.

Device list

Device list is loading. Please wait.

Device list

Confirm number of devices found on the Bus.

WTC

System device

Room device 2

Selected button

and confirm device list.

4. Set compact version

Check the version of the fresh water storage tank on the name plate.
Set compact version and confirm.

Integra

: WAS 100

Power

: WAS ... Power

System device

Which compact version is available?

Integra

Select

and confirm.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands