manualshive.com logo in svg

Weishaupt W-FM 25, Manual

Share
Download
Weishaupt W-FM 25 Manual Download Page 57

7 Troubleshooting

7.1 Procedures for fault conditions

CAUTION

Damage resulting from incorrect servicing

The combustion plant could be damaged.

▶

Do not carry out more than 2 lockout resets successively.

▶

Faults must be rectified by qualified personnel.

7.1.1 Display off

If the burner does not start despite heat demand:

▶

Check voltage supply

▶

Check unit fuse F7 (see Ch. 3.1).

▶

On burner size W30 and W40, the contactor can be fitted to a separate voltage

supply from the burner motor if required (contactor available as accessory).

▶

Check function and setting of all regulating, control and safety devices.

▶

Check all burner related functions.

7.1.2 Display flashes

A burner fault has occurred. The burner is in lockout. The error code is displayed

flashing.

Fault codes

▶

Read error code, e. g. 

A7h

.

▶

If required, additional information can be displayed by pressing the key

(see Ch. 7.1.3).

▶

Rectify cause of fault (see Ch. 7.2).

Resetting

▶

Press [ENTER] key.

✓

Burner has been reset.

Fault memory

The last 9 faults are saved in the fault memory (see Ch. 4.2.2).

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

7 Troubleshooting

83294002 • 2/2014-11 • La

57-70

Summary of Contents for W-FM 25









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands