background image

2-1/8"

54 mm

1"

25 mm

A

or

or

1 / 4

Required tools

Ruler

4 AA Batteries

Hammer

Wood 
block

Phillips screwdriver

Outils additionnels (en fonction de l’application)

E

N

G

LI

SH

67532
Rev 02
SED9400

Installation and User Guide

Weiser  

Technical Support

1-800-501-9471

www.weiserlock.com

If drilling a new door, use the supplied template and the complete door drilling 
instructions available at www.kwikset.com/doorprep

bac

kse

t

Measure to confirm that the hole in 
the door is 2-1/8" (54 mm).

Measure to confirm that the backset is 
either 2-3/8" or 2-3/4" (60 or 70 mm).

2-3/8" or 2-3/4"

60 or 70 mm

1-3/8" or 1-3/4"

35 mm or 44 mm

Measure to confirm that the hole in 
the door edge is 1" (25 mm).

Measure to confirm that the 
door is either 1-3/8" or 1-3/4" 
(35 mm or 44 mm) thick.

A

B

C

D

Latch

Exterior Assembly

Interior Cover

Strike

Parts in the box

Mounting Plate

Interior 
Assembly

Align tabs with 
holes in collar.

Install latch 
in door 
with wood 
block and 
hammer.

Ensure collar 

snaps into place.

Pull collar to 

test for tight fit.

Make sure 
slotted hole 
is at bottom 
of latch.

A

B

C

D

Is the door edge chiseled?

Hold the latch in front of the door hole, with the 
latch face flush against the door edge.

Make sure the latch bolt is fully retracted 
(in the unlocked position).

Install strike on the door frame.

180°

unlocked

door frame

 Make sure hole in door frame is drilled a 

minimum of 1” (25 mm) deep.

not 
chiseled

chiseled

Install latch in door 

with supplied screws.

If needed, change 
latch plate

Use a flathead screwdriver to 

lift tabs on collar of rectangular 

face to remove it from latch. 

Install drive-in collar.

Is the slotted hole centered in the door hole?

YES

NO

slotted hole  
is centered

slotted hole is 
NOT centered

No adjustment is 
required. Proceed 
to next step.

Rotate latch 
face as shown to 
extend latch.

Make sure 
slotted hole is at 
bottom of latch.

Yes

NO

Latch and 
Strike Screws

Tailpiece

Interior Assembly 
Screws

Mounting Plate Screws

For 1-3/4" 
thick doors

For 1-3/8" 
thick doors

G

E

C

A

A2

B

D

F

C

A

(x2)

(x2)

B

A

A2

A

A

H

J

K

L

M

1

Prepare the door and check dimensions

2

Install the latch and strike

Summary of Contents for Powerbolt 1

Page 1: ...ure collar snaps into place Pull collar to test for tight fit Make sure slotted hole is at bottom of latch A B C D Is the door edge chiseled Hold the latch in front of the door hole with the latch face flush against the door edge Make sure the latch bolt is fully retracted in the unlocked position Install strike on the door frame 180 unlocked door frame Make sure hole in door frame is drilled a mi...

Page 2: ...e batteries only F Test the turnpiece for smooth rotation D Secure the interior assembly with the supplied screws E Install the interior assembly C Align the colored edges of the connectors and ensure a tight cable connection B Insert the tailpiece into the slot of the latch A Ensure correct polarity Match the red color on both pieces to avoid damaging connector Align slot to tailpiece cable in bo...

Page 3: ...You will hear 2 long beeps Press and release PROG You will hear 2 long beeps Press Press 12 Press Press 56 B C B C Press PROG You will hear 1 long beep Press PROG You will hear 1 long beep D D Left Locking Latch If bolt goes left Right Locking Latch If bolt goes right What is the location of the latch exterior side of door interior side of door interior side of door interior side of door interior ...

Page 4: ...ave not been altered without your knowledge 5 Protect your User Codes 6 Dispose of used batteries according to local laws and regulations CAUTION Prevent unauthorized entry Since anyone with access to the interior assembly can reset the lock and change the User Codes you must restrict access to the interior assembly and routinely check the User Codes to ensure they have not been altered without yo...

Reviews: