Weinzierl 5326 Operation And Installation Manual Download Page 7

Page: 7 / 36

Seite 7/36

7 Mounting and delivery

7.1 Mounting

Mounting of the KNX RF / ENO Push Button 440

secure

①

▪

Insert the device

①

from above into the holding frame

②

. The device snaps into the

retaining lugs

③

of the holding frame on the left and right and sits flush on the four

retaining lugs

④

▪

Fasten the wall mounting frame

⑤

in the desired installation position (with screws or

adhesive pad)

– make sure that the retaining straps

⑦

point up and down.

▪

Place the decorative frame

⑥

on the wall mounting frame

⑤

and then place the device

①

locked into the holding frame

②

from above. The wall mounting frame

⑤

snaps into the

retaining lugs

⑧

of the holding frame

②

with the retaining straps

⑦

▪

Finally, place the rocker

⑨

(single rocker or double rocker depending on the model) on the

KNX RF / ENO Push Button 440

secure

①

and clip it in.

For dismantling, proceed in reverse order.

Summary of Contents for 5326





































Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands

Weinzierl 5326, Operation And Installation Manual

Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands