manualshive.com logo in svg

WEIHONG NK300CX, Manual

Share
Download
WEIHONG NK300CX Manual Download Page 38

上海维宏电子科技股份有限公司

 

SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD

 

38

 / 

53

 

3.2.1

 

Execute Fixed Calibration 

This operation is used to measure the tool on a certain fixed position of the machine 
tool to reconfirm tool offset. It helps to avoid tool length and the clamping position 

vary during calibration due to tool damage or other causes. 

It is mainly used for multi-tool mode and mainly used in the machine tool with tool 

magazine. 

Before executing fixed calibration, do the following: 

1.

 

Ensure parameter 

Calibration Type

 is set to 

1

. 

2.

 

Modify the value of parameter 

N75210 Fixed Presetter Position

 according to 

the actual situation. 

To execute fixed calibration, do the following: 

1.

 

To enter into 

Coor

 interface, in 

Auto

 / 

JOG

 / 

Handle

 / 

Step

 mode, press 

 → 

1

. 

2.

 

Press 

F5

. 

Fixed Calibrate (Measure Tool Length)

 dialog box pops up: 

 

 

 

3.

 

To select the target tool, input the target tool number in 

Define Tx

 input box. 

4.

 

To start fixed calibration, press 

F1

. 

 

 

Note:

 When the target tool number is different from that of current tool number, the system will 

automatically change the tool before fixed tool calibration. 

 

 

Summary of Contents for NK300CX























































Reviews:

No comments

Brands by name

Popular brands

Load more brands