Weidmuller IE-WL-BL-AP-CL User Manual Download Page 47

Page: 47 / 76

Wi-Fi device IE-WL-BL-AP-CL

Web Console Configuration

3-47

1st / 2nd trap version

Setting

Description

Factory Default

SNMP trap defined in SNMPv1

SNMP trap defined in SNMPv2

1st / 2nd trap server IP/name

Setting

Description

Factory Default

IP address or host
name

Enter the IP address or name of the trap server used by your
network.

None

1st / 2nd trap community

Setting

Description

Factory Default

Max. of 31 characters Use a community string match with a maximum of 31

characters for authentication.

Alert

Status

Wireless LAN Status

The status for

802.11 Information

parameters, such as Operation mode and Channel, are shown on the

Wireless Status

page. The status will refresh every 5 seconds if the

Auto Update

box is checked.

Certain values for

802.11 Information

might not be displayed based on the different operation modes

selected. For example, the

Current BSSID, Signal strength,

and

SNR

parameters

are not available in the AP

mode.

It is helpful to use the continuously updated information on this page, such as

Signal strength, Noise floor,

and

SNR

, to monitor the signal strength of the IE-WL-BL-AP-CL in Client mode.

Summary of Contents for IE-WL-BL-AP-CL













































































Search results

Summary of Contents for IE-WL-BL-AP-CL

Reviews:

Related manuals for IE-WL-BL-AP-CL

Brands by name

Popular brands

Weidmuller IE-WL-BL-AP-CL, User Manual

Search results

Summary of Contents for IE-WL-BL-AP-CL

Reviews:

Related manuals for IE-WL-BL-AP-CL

Brands by name

Popular brands