Weidmuller IE-WL-BL-AP-CL User Manual Download Page 23 | Manualshive

Page: 23 / 76

background image

Wi-Fi device IE-WL-BL-AP-CL

Web Console Configuration

3-23

Daylight saving time

Setting

Description

Factory Default

Enable/ Disble

Daylight saving time (DST or summer time) involves advancing
clocks (usually 1 hour) during the summer time to provide an
extra hour of daylight in the afternoon.

Disable

When

Daylight saving time

is enabled, the following parameters will be shown:

•

Starts at:

The date that daylight saving time begins.

•

Stops at:

The date that daylight saving time ends.

•

Time offset:

Indicates how many hours forward the clock should be advanced.

Time server 1/2

Setting

Description

Factory Default

IP/Name of Time
Server 1/2

IP or Domain name of the NTP time server. The 2nd NTP server
will be used if the 1st NTP server fails to connect.

time.nist.gov

Time sync interval

Setting

Description

Factory Default

Time interval for NTP
server synchronization
(600 to 9999 seconds)

This parameter determines how often the time is synchronized
from the NTP server.

600 (seconds)

Wireless LAN Setup

The IE-WL-BL-AP-CL provides the AP/client mode for point-to-multipoint communication.

AP/client:

The IP-Bridging mechanism is used to overcome limitations of the 802.11 standards. In this case,

the MAC address of the devices connected to the client radio will be replaced with the client’

s MAC address.

Under AP/client modes, communication problems might be encountered when you have a MAC authenticated
system or MAC (Layer 2) based communication. In this case, you will need to change the network to use the
master/slave operation mode.

Sniffer:

In order to provide an easier way for our customers to analyze wireless traffic, the IE-WL-BL-AP-CL

supports a “Sniffer” mode to co

-work with Wireshark packet sniffer software.

NOTE

Although it is more convenient to use dynamic bridging, there is a limitation

—

the Client can only transmit

IP-based packets between its wireless interface (WLAN) and Ethernet interface (LAN); other types of traffic
(such as IPX and AppleTalk) are not forwarded.

Operation Mode

The IE-WL-BL-AP-CL supports three operation modes

—

AP, Client, and Sniffer

—

each of which plays a distinct

role on the wireless network.

«
...
21
22
23
24
25
...
»

Summary of Contents for IE-WL-BL-AP-CL













































































Reviews:

No comments

Related manuals for IE-WL-BL-AP-CL

Brand: IDENTEC SOLUTIONS Pages: 17

Brand: D-Link Pages: 3

Brand: D-Link Pages: 2

Brand: Baracoda Pages: 2

Brand: Baracoda Pages: 2

Wi-Fi Bubble SpitFire

Brand: NAUTITECH Pages: 22

NUCLIAS CONNECT DAP-2680

Brand: D-Link Pages: 48

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 25

Brand: D-Link Pages: 26

nuclias connect DAP-2662

Brand: D-Link Pages: 12

Nuclias Connect DAP-2622

Brand: D-Link Pages: 86

Brand: D-Link Pages: 18

Nuclias Connect DAP-2622

Brand: D-Link Pages: 8

Nuclias DBA-2520P

Brand: D-Link Pages: 8

Brand: D-Link Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands