WEG SSW900 Series Installation Manual Download Page 1

English

Installation Guide

Enclosure Size 3C Ventilation Kit

SSW07/SSW08/SSW900

1 CONTENT

Table 1.1: 

Contents of the Kit

SSW07/SSW08 Enclosure Size 3 Ventilation Kit (Part number: 10935559)

Quantity

Description

1

SSW07/SSW08 enclosure size 3 ventilation kit

SSW900 Enclosure Size C Ventilation Kit (Part number: 10935559) 

Quantity

Description

1

SSW900 enclosure size C ventilation kit 

2 SAFETY NOTICE

ATTENTION!

Isolate electrically the Soft-Starter SSW07/SSW08/SSW900 before 
installing the Ventilation Kit. The electronic boards have components that 
are susceptible to electrostatic discharge. Never touch any of the electrical 
components or connectors without following the proper grounding 
procedures. It is reccomended the use of a grounding wrist strap.

3 APPLICATION

This optional module improves the thermal capacity of the Soft-Starter.

The Ventilation kit is connected directly to the SSW07/SSW08/SSW900. The 
module fits in the bottom of the Soft-Starter, at the heatsink.

NOTE!

This kit is reccommended when more than 3 starts per hour (every 20 
minutes) is required at the following conditions: 3 x In during 30 s (SSW07 
and SSW900) or 3 x In during 20 s (SSW08) with an ambient temperature 
of 55 ºC (131 °F).

NOTE!

The fans are controled by the heatsink temperature. Thus it will only start 
when required and usually during acceleration and deceleration ramp.

4 VENTILATION KIT INSTALLATION PROCEDURE

1. Those are the contents of the kit.

2. Snap the kit into the holes located near the edges of the heatsink, at the 

bottom of the SSW07/SSW08/SSW900.

3. Connect the power supply cable at the terminal presented in the figure.

4. Make sure that the support and the cable are connected.

Español

Guia de Instalación

Kit Ventilación para Tamaño 3C

SSW07/SSW08/SSW900

1 CONTENIDO 

Tabla 1.1: 

Contenido del Kit

Kit Ventilación para el Tamaño 3 del SSW07/SSW08 (Código: 10935559)

Cuantidad

Descripción

1

Kit de ventilación para el tamaño 3 del SSW07/SSW08

Kit Ventilación para el Tamaño C del SSW900  (Código: 10935559) 

Cuantidad

Descripción

1

Kit de ventilación para el tamaño C del SSW900    

2 INFORMACION DE SEGURIDAD

¡ATENCIÓN!

Aislar eléctricamente el Arrancador Suave SSW07/SSW08/SSW900 antes 
de instalar el kit ventilación. Las tarjetas electrónicas utilizan componentes 
sensibles a descargas electrostaticas. No tocar directamente sobre los 
componentes o conectores. Se recomienda el uso de una pulsera de 
puesta a tierra.

3 APLICACIÓN

Este módulo opcional mejora la capacidad térmica del Arrancador Suave.

El Kit Ventilación para la Tamaño 3 es conectado directamente al SSW07/
SSW08/SSW900. El módulo encaja en la parte inferior del Arrancador Suave 
junto al disipador.

¡NOTA!

Este kit es recomendado cuando hay de más de 3 arranques por hora 
(cada 20 minutos) en las siguientes condiciones: 3 x In durante 30 s 
(SSW07 y SSW900) o 3 x In durante 20 s (SSW08) con temperatura 
ambiente de 55 ºC.

¡NOTA!

Los ventiladores son controlados por la temperatura del disipador de calor. 
Por lo tanto, sólo se encenderá cuando sea necesario, y normalmente 
durante la rampa de aceleración y desaceleración.

4 PROCEDIMIENTO PARA LA INSTALACIÓN DEL KIT 

VENTILACIÓN

1. Este es el contenido del kit.

2. Encajar el kit en la nuración ubicada en la lateral del disipador en la parte 

inferior del SSW07/SSW08/SSW900.

3. Conectar el cable de alimentación en el terminal presentado en la figura.

4. Certifíquese que el soporte y el cable estén conectados.

Document:  0899.5543 / 0

3

10193003

Reviews: