WEG PSRW User Manual Download Page 45 | Manualshive

Page: 45 / 59

background image

Programming With WPS

PSRW | 9-11

9

The buttons Exit from Prog-mode

, monitoring

and transfer

are used to transfer configurations

to PSRW and they will be explained in the following sections.

9.4.2 Wizard Monitor

The following figure shows the user interface of the Monitor.

Configuration

viewer area

PSRW_Monitor

Buttons

Configuration viewer area:

area where is possible to view configurations from PSRW. A more detailed explanation

will be given in the following sections.

Wizard Monitor Buttons:

displays commands for zoom in/out

, validate configurations on physical

PSRW

, enter in Prog-mode

and exit from Prog-mode

.

The buttons Exit from Prog-mode

and Validate configurations on physical PSRW

, are used to

transfer configurations to PSRW and they will be explained in the following sections.

9.5 DESIGNING A CONFIGURATION

To design a configuration, it is necessary to open the wizard Configurator and configure the component blocks
described in the following sections.

«
...
43
44
45
46
47
...
»

Summary of Contents for PSRW




























































Reviews:

No comments

Related manuals for PSRW

EASY412-AC Series

Brand: Eaton Pages: 12

Brand: ABB Pages: 20

Brand: ABB Pages: 32

Relion RER615 DNP3

Brand: ABB Pages: 36

Brand: ABB Pages: 36

Brand: Littelfuse Pages: 82

Brand: ABB Pages: 24

Circuit Shield 87B

Brand: ABB Pages: 15

Brand: ABB Pages: 12

Brand: Savant Pages: 2

Brand: Savant Pages: 2

Brand: Chromalox Pages: 8

Brand: macromatic Pages: 2

Brand: Greystone Energy Systems Pages: 2

Brand: GE Pages: 78

Brand: ALIND Pages: 54

Brand: ABB Pages: 124

Brand: ABB Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands