manualshive.com logo in svg

Wecon LX3V-4AD, User Manual, Page: 9 / 12

Share
Download
Wecon LX3V-4AD User Manual Download Page 9

                                                                                                                                                 

LX3V-4AD

 

8                                                       

                                                                       

WECON TECHNOLOGY CO., LTD.

 

 

Offset is the “Position” of the calibrated line, identified at a digital value of 0. 

(d) Negative offset. 

(e) Zero offset: Default is 0V or 4mA. 

(f) Positive offset. 

 

 

 

Offset  and  gain  can  be  set  independently  or  together.  Reasonable  offset  ranges  are  -5  to  +5V  or 

-20mA to 20mA,  and  gain  values  1V  to  15V  or 4mA  to 32mA.  Gain and offset  can be  adjusted by 

software in the LX3V main unit (please refer to program example 2). 

 

Bit device’s b1, b2 of the gain/offset BFM #21 should be set to 0, 1 to allow adjustment. 

 

Once  adjustment  is  complete  these  bit  devices  should  be  set  to  1,  0  to  prohibit  any  further 

changes. 

 

Channel initialization (BFM #0) should be set to the nearest range, i. e. voltage/current etc. 

 

6.

 

Example program 

 

6.1 basic program 

In the following example channels CH1 and CH2 are used as  voltage inputs. The LX3V-4AD block is 
connected at the position of special function block No.0. Averaging is set at 4 and data registers D0 

and D1 of the PC receive the averaged digital data. 

 

Summary of Contents for LX3V-4AD













Reviews:

No comments