Wecon LX3V-4AD User Manual Download Page 2 | Manualshive

Page: 2 / 12

Wecon LX3V-4AD User Manual Download Page 2

LX3V-4AD

1

WECON TECHNOLOGY CO., LTD.

1.

Introduction



The LX3V-4AD special module has four input channels. The input channels receive analog

signals and convert them into a digital value. This is called an A/D conversion; the maximum

resolution is 16 bits.



The selection of voltage or current based input/output is by user wiring. Analog ranges of -10 to

10V DC (resolution: 5mV), and/or 4 to 20mA, -20 to 20mA (resolution: 20µA) may be selected.



Data transfer between the LX3V-4AD and the LX3V main unit is by buffer memory exchange.

There are 32 buffer memories (each of 16 bits) in the LX3V-4AD.



LX3V-4AD consumes 5V voltage from LX3V main unit or active extension unit, 90mA current of

power supply.

2.

Dimensions

① Extension cable and connector

② COM LED: Light when communicating

③ Power LED: Light when connect to 24V

④ State LED: Light when normal condition

⑤ Module name

⑥ Analog signal output terminal

⑦ Extension module interface

⑧ DIN rail mounting slot

⑨ DIN rail hook

«
1
2
3
4
...
»

Summary of Contents for LX3V-4AD













Reviews:

No comments