manualshive.com logo in svg

Wecon LX3V-4AD, User Manual, Page: 12 / 12

Share
Download
Wecon LX3V-4AD User Manual Download Page 12

                                                                                                                                                 

LX3V-4AD

 

11                                                       

                                                                       

WECON TECHNOLOGY CO., LTD.

 

2)

 

Check  that  the  LX3V  system  configuration  rules  have  not  been  broken,  i.e.  the  number  of 

special function blocks does not exceed 8 and the total system I/O is equal or less than 256 I/O.   

3)

 

Ensure that the correct operating range has been selected for the application. 

4)

 

Check that there is no power overload on either the 5V or 24V power sources, remember the 

loading  on  a  LX3V  main  unit  or  a  powered  extension  unit  varies  according  to  the  number  of 

extension blocks or special function blocks connected. 

5)

 

Put the LX3V main unit into RUN. 

 

7.2 Error checking 

 

If the LX3V-4AD special function block does not seem to operate normally, check the following 

items. 

Check the status of the POWER LED. 

Lit: The extension cable is properly connected. 

Otherwise: Check the connection of the extension cable. 

 

Check the external wiring. 

 

Check the status of the “24V” LED (top right corner of the LX3V-4AD). 

Lit: LX3V-4AD is OK; 24V DC power source is OK. 

Otherwise: Possible 24VDC power failure, if OK possible LX3V-4AD failure. 

 

Check the status of the “A/D” LED (top right corner of the LX3V-4AD). 

Lit: A/D conversion is proceeding normally. 

Otherwise: Check buffer memory #29 (error status). If any bits (b2 and b3) are ON, then this is 

why the A/D LED is OFF. 

 

 

 

 

 

 

 

 

 

 

 

 

 
Version: V3.0.1 

Date: April 2019 

Summary of Contents for LX3V-4AD













Reviews:

No comments