Webfleet LINK 710 Installation Manual Download Page 30 | Manualshive

Page: 30 / 38

background image

Connect a latched switch to IN as shown below.

If the switch is on (connected to vehicle voltage), the logbook mode is set to Private
trip. If the switch is off (connected to GND), the logbook mode is set to Business
trip.

Using the input IN for idle time reporting

Your LINK 710 can report idle times to WEBFLEET when the engine is running for
longer than five minutes and the vehicle is not moving. This requires configuration in
WEBFLEET.

The input IN must be connected to a signal indicating the activity of the engine, for
example alternator, engine, etc. The input IN must be active when the engine is

running.

30

«
...
28
29
30
31
32
...
»

Summary of Contents for LINK 710







































Reviews:

No comments

Related manuals for LINK 710

Brand: WatchDog Pages: 3

TripMaker RVND 5510

Brand: Rand McNally Pages: 21

Brand: RAK Pages: 10

010-11018-00 - Mobile PC - GPS Software

Brand: Garmin Pages: 1

LONE WORKER ALARMS NZ

Brand: MERCARI Pages: 6

BackTrack D-TOUR 360310BG

Brand: Bushnell Pages: 60

Brand: Haicom Pages: 32

Brand: Num'axes Pages: 84

Brand: SRT Pages: 2

Intelliroute TND-510

Brand: Rand McNally Pages: 148

Professional activity level tracker

Brand: Activ8 Pages: 2

Brand: Becker Pages: 22

Brand: Dyegoo Pages: 30

Brand: AIRIS Pages: 45

Brand: SkyCaddie Pages: 30

Brand: RoyalTek Pages: 18

Brand: RoyalTek Pages: 23

Brand: RoyalTek Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands