Weber Markoprint XB4JET Manual For Installation, Operation And Maintenance Download Page 28 | Manualshive

Page: 28 / 162

Weber Markoprint XB4JET Manual For Installation, Operation And Maintenance Download Page 28

Transport, packaging and storage

72800153 Markoprint XB4JET / XB8JET

Seite 28 von 162

GB

Transport, packaging and storage

Installation  and  commissioning  is  performed  exclusively  by  the  manufacturer’s
staff or by persons authorised by the manufacturer.
However,  in  the  course  of  installation,  operators  or  maintenance  staff  of  the
operating  company  may  be  entrusted  with  the  handling  of  packages.  In  this
respect, be sure to observe the notes below.

Safety notes on transport

Improper transport

CAUTION!

Damage arising from improper transport!

Improper transport may cause significant material damage.
Therefore:
– When offloading packages delivered and in the course of internal
transport, proceed with caution and observe the symbols and instructions
on the packaging.
– Only remove packaging when ready for assembly.

«
...
26
27
28
29
30
...
»

Summary of Contents for Markoprint XB4JET



































































































































































Reviews:

No comments