manualshive.com logo in svg

WebDoor CADET PRO, Installation And Instruction Manual, Page: 1 / 32

Share
Download
WebDoor CADET PRO Installation And Instruction Manual Download Page 1

 

 
 

 

 
 

WebDoor 
866-262-5661 

[email protected] 
www.webdoor.com 

 
                             

Issued Date: 2017-03-28 

 CADET PRO (Non-Handed)  

LOW ENERGY SWING DOOR OPENER

 

Installation and Instruction Manual

 

 

 

 

 

 

 

 

1.  READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY! FAILURE TO DO SO MAY RESULT IN 

PERSONAL INJURY OR PROPERTY DAMAGE! 

2.  Install only on a properly operating and balanced door. A door that is operating improperly could cause severe injury. 

Have qualified service personnel make repairs to cables, spring assemblies, and other hardware before installing the 
opener. 

3.  Remove all pull ropes and remove, or make inoperative, all locks (unless mechanically and/or electrically interlocked 

to the power unit) that are connected to the door before installing the opener. 

4.  Install the door opener at least 8 feet or more above the floor if the opener has exposed moving parts. 
5.  Do not connect the door opener to the source of power until instructed to do so. Connection of the high voltage supply 

should be done by a qualified professional and within the guidelines of the enforced local electrical codes. 

6.  Locate the control station: (a) within sight of the door, (b) at a minimum height of 5 feet so small children cannot reach 

it, and (c) away from all moving parts of the door. 

7.  Install the Entrapment Warning Placard next to the control station in a prominent location. 
8.  For products having a manual release, instruct the end user on the operation of the manual release. 
9.  Test all safety features before turning over the equipment to the customer. 

 

Summary of Contents for CADET PRO

































Reviews:

No comments