background image

Fault finding and Useful conversions

PROBLEM 

SOLUTION                        PAGE

ANGEL WILL NOT FIRE

No air or nitrogen present? 

Propellant Air/Nitrogen Supply . 

6

Is the battery operational? 

Change the battery 

4

Is the ANGEL in ‘SAFE’ 

Making the ANGEL ‘LIVE’. 

3/4

Is the trigger not closing the switch? 

Trigger Adjustment. 

29/30

Is the trigger not releasing the switch? 

Trigger Adjustment. 

29/30

Is the bolt jammed forward? 

Clear the blockage from breech. 

Is the LPR set correctly? 

LPR Adjustment.  

24

Is the OPTO Trigger functioning? 

Trigger Adjustment. 

29/30

Are the connectors plugged in correctly? 

Wiring Connections 

30

Are the Angel Eyes switched on? 

Ensure paint is present 

Are the Angel Eyes optics blocked 

Clean the Angel Eyes Optics 

VELOCITY VARIATIONS

Are good quality paintballs been used? 

Use good paintballs. 

Is the barrel bore correct for the paint? 

Use suitable barrel. 

Is the paint swollen, cold or hot?  

Review your storage of paint. 

Is the barrel bore clean? 

Clean the barrel. 

Is the tank reg choking on gas supply? 

Check tank regulator assembly. 

-

Is the tank reg operating correctly? 

Check tank regulator assembly. 

-

Is the mini-reg operating correctly? 

Mini-Regulator Service. 

20 

Is the mini-reg choking on gas supply? 

Mini-Regulator Service. 

20

Are unsuitable after market parts fitted? 

Use genuine ANGEL parts. 

Is the bolt worn? 

Replace Soft Bolt. 

7

Is the LPR set correctly? 

LPR Adjustment. 

24

Is the valve dwell set correctly? 

Dwell Adjustment. 

13

Is first shot low? 

Increase Dwell Time 

13

VELOCITY TOO LOW / HIGH 

Is the high pressure reg set correctly? 

Check at gas source. 

6

Is velocity adjuster screw set correctly? 

Velocity adjustment.                      

7

Is the bolt sticking? 

Check rubber finger detents.  

21

Is the LPR set correctly? 

LPR Adjustment. 

24

Is the valve dwell set correctly? 

Dwell Adjustment. 

13

GAS LEAKING

From the back cover? 

Check solenoid valve. 

19

From the Ram assembly? 

Check ram body O rings. 

28

From the gas joints? 

Check all fittings. 

18/19

From exhaust valve? 

Exhaust valve stem/guide. 

27

Useful conversions 

 

Listed are some useful conversions 

relating to pressure, velocity, mass  

and distance. 

PRESSURE

1 atm = 1.01325 bar
1 atm = 14.6959 psi
1 bar = 14.5038 psi
1 psi = 0.0689476 bar 

VELOCITY

1 Ft/s = 0.3048 m/s
1 Ft/s = 0.6818180 Mph
1 m/s = 3.28084 Ft/s
1 m/s = 2.23694 Mph
1 m/s = 3.6 Kph 

MASS

1 g = 0.05274 oz
1 Kg = 2.20462 Ib
1 oz = 0.0283495 Kg 

DISTANCE

1 mm = 0.0393701 Inch
1 Inch = 25.4mm
1 thou = 25.4 micron
1 micron = 0.0393701 thou 

FORMULA TO CONVERT
FEET PER SECOND (Ft/s) 
TO FOOT Lbs (Force)

1 foot Ibs (force) = 1.35582 Joules
1 Joule = 0.737562 foot Ibs (force)
1 Gram = 15.4324 Grains
1 Grain = 0.000142857 lb
1 lb = 7000 Grains

Velocity squared x Projectile weight 
VELOCITY = Ft/s (feet per second) 
PROJECTILE WEIGHT = GRAINS 
Therefore a paintball @ 3.2grams  
@ 300Ft/s= 9.9 foot lbs (ftlbs)

Summary of Contents for ANGEL





































Reviews: