WCP GreyT Elevator V3 User Manual Download Page 6 | Manualshive

Page: 6 / 42

background image

GreyT Elevator V3 - User Guide

(Rev 1)

Page 6

Table of Contents

wcproducts.com

Tubing Cut Guide

The overall length for these tubes is for the elevator represented in the CAD model. This

can be changed to fit the requirements of any design.

Ensure that when cutting tubes, the distance from the last hole to the end of the tube

is the same as the image below. Usually this means that the tube length must be in

1/2” increments. This distance is required for the bearing blocks and tube plugs to fit

properly. If VersaFrame tubing is not used then tubes can be any length.

Note: It is recommended to cut the tubes longer than needed and then mill to the

correct length� Alternately, a chop saw may be used� The ends of the tubes should be

as flat and square as possible.

«
...
4
5
6
7
8
...
»

Summary of Contents for GreyT Elevator V3











































Reviews:

No comments

Related manuals for GreyT Elevator V3

Brand: S&S Northern Pages: 9

Brand: ICP DAS USA Pages: 8

Brand: Measurement Computing Pages: 32

Brand: heat-timer Pages: 36

Metalmaster 200d Pro DC GTAW

Brand: Tokentools Pages: 33

WELDER FANTASY BI-PULSE 201

Brand: FACHOWIEC Pages: 33

Drive 4 Basic S

Brand: EWM Pages: 52

VORTEX PRECEDENCE G1

Brand: EXTOL Pages: 104

Brand: GYS Pages: 60

Brand: Ergoswiss Pages: 27

Brand: Ravaglioli Pages: 68

THERMASGARD 9112

Brand: S+S Regeltechnik Pages: 48

Brand: SMAR Pages: 47

Brand: Eaton Pages: 15

LogiCORE IP v1.02a

Brand: Xilinx Pages: 57

Brand: Jasic Pages: 29

Brand: Vahle Pages: 100

Brand: BFT Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands