manualshive.com logo in svg

WBOX Technologies WBXHD041S, User Manual

Share
Download
WBOX Technologies WBXHD041S User Manual Download Page 41

Camera Management 

Digital Video Recorder(DVR) 

User Manual 

 

Issue V1.0 (2018-06-04) 

 

33 

 

Figure 5-8

 

Processing method screen 

 

 

 

2.

 

Click 

  of  “Buzzer  alarm”,  Push  message”,  “Alarm  message”,  “Linkage 

record” respectively to enable or disable these function.

 

3.

 

Click 

OK

 to save processing method settings or click 

Cancel

 to cancel the settings.

 

Step 6

 

Click 

OK

 to save video loss settings or click 

Copy to all

, then click 

OK

 to apply the 

video loss settings to cameras of all channels. 

----End 

5.5 Motion Detection 

Motion detection refers that an alarm is triggered when an image in a specified area 
changes. 

Operation Description 

Click 

Menu

 in the upper left corner of the camera management screen and choose 

Motion Detection

 to access the 

Motion Detection

 screen, as shown in Figure 5-9. 

Summary of Contents for WBXHD041S



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands