manualshive.com logo in svg

Waygate Technologies Krautkramer USM 10, Operating Manual

Share
Download
Waygate Technologies Krautkramer USM 10 Operating Manual Download Page 56

3  Initial start-up

Remote Connection Setup

56

Rev. - (09/2021)

Krautkrämer USM 100

3.7 Remote Connection Setup

The USM 100 supports Virtual Network Computing 
(VNC). 

The VNC client displays the screen contents of a remote 
device on a local computer (client) and in return sends 
keyboard and mouse movements of the local computer 
to the remote device. 

Prerequisites

● Computer with installed VNC client

● USB-C hub with RJ45 connector

● Network cable

VNC Client

To view and control the instrument‘s screen remotely 
you must have a VNC client installed on your computer. 

As VNC is a standard protocol, any client application 
which supports VNC protocol can be used to remotely 
control the USM 100. The recommendation is to use 
RealVNC or TightVNC. 

You can download the software from the respective site 
and install it on your computer:

https://realvnc.com/en/connect/download/viewer

https://tightvnc.com/download.php

After downloading, follow the respective installation in-
structions. 

Summary of Contents for Krautkramer USM 10



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands