Wavecom FASTRACK M1306B User Manual Download Page 45

Page: 45 / 55

WM_PRJ_M13_UGD_001 - 001

20th July 2004

Wavecom Confidential & Proprietary Information

Page:

This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged
without prior written agreement.

8.2 Electrical characteristics

8.2.1 Power supply

Table 8: Electrical characteristics

Operating Voltage

ranges

5.5 V to 32 V DC (GSM or DCS or GPRS).

Maximum current

480 mA Average at 5.5V.

1.7 A Peak at 5.5 V.

Note: the modem is permanently powered once the power supply is connected.

The following table describes the consequences of overvoltage and undervoltage

with the Fastrack Modem.

Table 9: Effects of power supply defect

If the voltage :

Then:

falls below 5.5 V

The GSM communication is not guaranteed.

Voltage over 32 V

(Transient peaks)

The modem guarantees its own protection.

Voltage over 32 V

(continuous overvoltage)

Protection of the modem by the fuse (the

supply voltage is disconnected).

The following table provides information on power consumption of the Fastrack

modem, assuming an operating temperature of +25 °C and using a 3 V SIM

card.

Summary of Contents for FASTRACK M1306B
























































Search results

Summary of Contents for FASTRACK M1306B

Reviews:

Related manuals for FASTRACK M1306B

Brands by name

Popular brands

Wavecom FASTRACK M1306B, User Manual

Search results

Summary of Contents for FASTRACK M1306B

Reviews:

Related manuals for FASTRACK M1306B

Brands by name

Popular brands