background image

Installation, Operation and Maintenance Manual

Models: 
Cold Bev Max-S2, Cold Bev Max-S2L, Cold Bev Max-S3L  
Cold Bev Max-S1BBL, Cold Bev Max-S2BBL, Cold Bev Max-S3BBL 

IOM-HS-Cold Bev Max

Important

Please read the entire manual before proceeding with  

the installation and startup. Your failure to follow any  

attached instructions or operating parameters may lead to  

the product’s failure.
Save manual for future reference

Table of Contents

System Specifications  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Replacement Filters  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 
Notice to Installers  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 
Installation Precautions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 
Operation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 
Installation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 
Maintenance   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 
Filter Cartridge Replacement Procedure   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 
Replacement Parts List   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 
System Drawings   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 
Limited Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6

Cold Bev Max-2BBL

Note:

 Do not use with water that is microbiologically unsafe or 

of unknown quality without adequate disinfection before or after 

the system .

Tested and certified by WQA against NSF/ANSI 

Standard 42 for the reduction of claims specified on 

the performance data sheet & NSF/ANSI 372 for "lead 

free" compliance .

Summary of Contents for Hydro-Safe Cold Bev Max-S2









Reviews: