background image

SmartPlate EV Installation, Operation and Maintenance Manual

 

CHAPTER 2 

– INSTALLATION  

 

 

OMM-0147_C 

•  SP-102 •  3/2/2021                Technical Support  •  (800) 526-0288  •  Mon-Fri, 8 am - 5 pm EST                Page 

13

  of 

72

 

 

  INSTALLATION

 

 

2.1  INTRODUCTION 

All of the SmartPlate EV Water Heater models are shipped fully assembled and ready for 
installation. Therefore, installation will consist of the following tasks: 

  Unpack the SmartPlate EV Water Heater from its shipping container. 

  Position and secure the unit at the site. 

  Install the Pressure Relief Valve.  

  On units installed in New York City, install a second Relief Valve on the boiler water intake 

piping. 

  Connect the hot boiler water piping to the unit. 

  Connect the domestic hot water (DHW) piping to the unit. 

  Connect external AC power to the ECS II Control Box. 

  If  desired,  connect  Modbus  control  wiring  to  the  Temperature  Controller  in  the  ECS  II 

Control Box. 

 

2.2  RECEIVING AND UNPACKING  

Each SmartPlate EV Water Heater is shipped as a single crated unit. The packaged shipping 
weight will vary from approximately 

500 

to 

760

 pounds, depending on the model ordered.  

The unit must be moved with the proper equipment (forklift, pallet jack, etc.) to avoid possible 
injury to personnel or damage to the shipping container or unit. The shipping carton should be 
inspected for damage incurred during transit prior to signing the bill of lading. 

NOTE: 

AERCO  is  not  responsible  for  lost  or  damaged  freight.  The  freight  carrier  must  be  notified 
immediately of any damage detected. 

Unpack the SmartPlate EV Water Heater from its shipping container taking care not to damage 
the unit when cutting away the packaging material.  

Remove the package containing the Relief Valve and associated piping.  

Remove the bolts securing the unit to its shipping skid and then lift it off the skid and position it 
in place. Perform a complete visual inspection of the unit to ensure there is no evidence of 
damage.  

 

 

 

Summary of Contents for Aerco SmartPlate EV









































































Reviews: