Watson Marlow Pumps 500 Series Installation, Operating And Maintenance Manual Download Page 152

Page: 152 / 157

Figure 34 - Marprene TH element, 4-7 bar(60-100 psi), 200 rpm, counter-clockwise rotation

ml/min

-1

100

150

200

250

300

350

400

450

3.2 mm

Suction (-) bar

Pressure (+) bar

Figure 35 - Maxthane LoadSure Elements, Counter clockwise Rotation 200 rpm RET rotor

ml/min

-1

500

1000

1500

2000

2500

3000

3500

9.6 x 1.6mm

6.4 x 1.6mm

3.2 x 1.6mm

Suction (-) bar

Pressure (+) bar

Note: To achieve the discharge pressures stated above, the rotor must be run counter clockwise. To
achieve optimal tube life, run the rotor clockwise at a maximum discharge pressure of 2 bar.

152

m-530pn-en-09 02-02-22

Summary of Contents for 500 Series






























































































































































Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands

Watson Marlow Pumps 500 Series, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands