Watson Marlow Pumps 500 Series Installation, Operating And Maintenance Manual Download Page 106

Page: 106 / 157

20.5

Dispense settings

Note: the pump must be stopped to enter

DISPENSE SETTINGS.

Select

MODE

Using the

∧

∨

keys, scroll to

DISPENSE

and press

SETTINGS

The following are available in dispense mode settings:

Active batch

Batch to be dispensed. Select from a list of created batches. To create a new batch refer to "Create a
new batch or edit a batch" on page 98

Batches

batch

contains the batch size, active recipe, direction and start and end delay. You must create at

least one batch and set it as the active batch before Dispense can start.

Batch parameters

Configure the following parameters:

106

m-530pn-en-09 02-02-22

Summary of Contents for 500 Series






























































































































































Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands

Watson Marlow Pumps 500 Series, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands