Watlow PC1X-N20, User Manual

Page: 21 / 73

Navigation
¨[````]¨[````]¨[load]¨[freq]¨
Single-Zone Single-Phase
¬®[In``] or [In|c] or [In|u] ¬®[`Out]¬®[`Hbt]¬%%% ®[`UoL]¬®[`Cur]¬®[`HUa]
Multi-Zone [```] Three-Phase [```]
%%%% [2one] %%%%%%% [PHAS]
Display Loop Use the Increment/Decrement keys ( Ó Î ) to select a Zone or Phase
within the Display Loop. The Zone/Phase appears in the upper display.
Use the Left/Right arrow keys (
¬ ®
) to select a parameter within a Zone or Phase.
The parameter appears in the bottom display.
Use the Increment/Decrement keys ( Ó Î ) to select a value, either alpha or
numeric, within a parameter. The value appears in the upper display.
Use the Home key ( ± ) to toggle between Zones/Phase 1, 2, or 3 sequentially.
(#)
Î
Ó
Display Zone
Selection Display Phase
Selection
(#)
Î
Ó
(code) (code)
Active Alarms
(if any)
[```1]
Zone 1
[```1]
Phase 1
[2one] % ¨[In1`]
or
[In|`c1]
or
[In|`u1] ¨[Out1]¨[Hbt1]¨[UoL1]¨[Cur1]¨[HUa1]¨% [`ph5] % ¨[UoL1]¨[Cur1]¨
% Î% ±% ±% ±% ±% ±% ±% ±% ±% Î% ±% ±%
% Ó%%%%%% Ó%
[```2] Zone 2 [```2] Phase 2
[2one] % ¨[In2`] or [In|`c2] or [In|`u2] ¨[Out2]¨[Hbt2]¨[UoL2]¨[Cur2]¨[HUa2]¨% [`ph5] % ¨[UoL2]¨[Cur2]¨[`HUa]¨
% Î% ±% ±% ±% ±% ±% ±% ±% ±%% Î% ±% ±%
% Ó%%%%%% Ó
[```3]
Zone 3
[```3]
Phase 3
[2one] % ¨[In3`]
or
[[In|`c3]
or
[In|`u3] ¨[Out3]¨[Hbt3]¨[UoL3]¨[Cur3]¨[HUa3]¨% [`ph5] % ¨[UoL3]¨[Cur3]¨
% Î% ±% ±% ±% ±% ±% ±% ±% ±% Î% ±% ±%
% Ó%%%%%% Ó
%
Press Home and Left Keys together
for 2 seconds to enter the Setup
Menus from the Display Loop.
Setup Page Menus
Factory Page Menus
Display Loop
±¬
± ±
Press Home Key from any menu to
return to the Display Loop.
% ±¬®
Press Home, Left and Right Keys all
together for 2 seconds to enter the
Factory Menus from the Setup Menus.
N a v i g a t i o n a n d S o f t w a r e , C h a p t e r 4 Wa t l o w P o w e r S e r i e s
■
4 . 3
NOTE: For an explanation of the parameters in the Display Loop, range information, Modbus address, and conditions for
the parameter to appear, see pp. 6.1-6.4, Chapter Six, Parameters.
NOTES:
What you see in each Page and in each Menu are factory set, depending on the options and settings of your controller.
The input signal method indicator will change depending on the input signal method chosen — digital, current, or volts.
Current operating parameters may be modified at any time with the use of the keypad or communications port.
The Display Loop is
used to monitor
parameters and adjust
manual/digital input,
and to clear alarms if
they are latched.
***8
***8