Our ClearWater II Cartridge Filter System is shipped from Waterway
complete with everything you need right in the box. Assemble filter
system only after above-ground pool is installed. Fill pool with water.
Do not raise water level above pool return line.
The pool equipment should be located between pool skimmer and
return line. The filtration system should not be closer than 2 ft. and not
further than 5 ft. from the pool. The ClearWater II Cartridge Filter System
needs to be on a completely flat surface (e.g. patio block, cement slab,
etc.). The pump will require a 110 volt/20 amp service.
WARNING: A GFCI is required. Follow national and local
building and safety codes.
Before opening shipping carton, make sure box is in the upright
position. Inside the carton, you will find:
1. One base
2. One pump (packaged in separate box)
3. One filter
4. Two lengths of 6 ft. hose
5. One bag with fittings
WARNING! READ ALL INSTRUCTIONS AND WARNING
LABELS BEFORE OPERATING FILTER!
1. Place filter and base on a level, secure surface. Open fittings bag and
remove coupling assembly (Detail 2). Assemble 2" gasket, coupling,
coupling o-ring, and 2" union nut, and thread into inlet side of filter.
2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union
nut. Hand tighten union nut to suction side of pump (Detail 2).
3. Place the pump on the base to the left of the filter. The pump should
align wth coupling on filter side marked “Inlet”. There is no need to
disassemble filter or pump assemblies.
4. Thread 2" union nut to pump discharge (Detail 2). Thread gate valve
with gasket to pump trap suction side (Detail 2).
5. Secure pump to base using the pin and anchor assemblies (Detail 1).
6. From the fittings package, remove 1 1/2" hose adapter and o-ring
(Detail 2). Thread into outlet side of the filter tank.
7. Remove 4 hose clamps from the fittings bag. Select one of the hose
lengths and slip one clamp over the end of the hose adapter. Place
the end of the hose on to the gate valve (pump suction) and the
other end to the hose adapter end of the pool skimmer. Repeat steps
with filter outlet to pool return.
8. Remove the lid handle, #4a, from the fittings bag and attach it to the
top of the lid assembly, #4, as shown (Detail 3). Secure Clearwater
Filter to Clearwater Filter Base using #15a phillips head screws (2),
(Detail 4 & 5). Fill pool until water level is halfway up length of
skimmer throat.
9. Open air release knob. Plug in and turn on pump. Air will pass out of
the filter through the air release knob. Once water discharges from
knob, close it.
NOTE
: To remove lid assembly, take off filter nut, #6, insert filter
wrench, #9a, in notch between filter body, #9 and lid assembly, #4,
twist and separate as shown in Detail 5.
CLEARWATER II CARTRIDGE FILTER SYSTEM OWNER’S MANUAL
CLEARWATER II CARTRIDGE FILTER SYSTEM REPLACEMENT PARTS
INSTALLATION INSTRUCTIONS
Item
Part No.
Description
1
830-4000SS
Pressure Gauge
1a
805-0224
O-Ring
1b
519-7431
Pressure Gauge - Fitting Adapter
1c
805-0117SD
O-Ring
2
602-0200
Air Relief Plug
3
805-0207
O-Ring - Air Relief
4
511-7327
Lid Assembly - Small (75 or 100 sq. ft.)
511-7337
Lid Assembly - Large (150 or 200 sq. ft.)
5
805-0460
Lid O-Ring
6
718-7251
Filter Nut
(sold with Lid Assembly only)
6a
519-7451
Lock-Tab
7
519-7441
Wing Nut
8
817-0075P
Cartridge - 75 sq. ft.
817-0100P
Cartridge - 100 sq. ft.
817-0150N
Cartridge - 150 sq. ft.
817-0200N
Cartridge - 200 sq. ft.
9
515-7257
Body – Filter Bottom
9a
519-7470
Filter Wrench (see Detail 5)
10
417-6240
1 1/2" MPT x 1 1/2" Smooth Male Hose Adapter
11
805-0224
O-Ring
12
872-9002
Corrugated Hose - Black
13
872-0010
Hose Clamp - Stainless Steel
14
500-5300
Drain Assembly
14a
505-2030
Drain Cap
15
672-7401
ClearWater II Base
15a
819-0004
#10 x 1 S/S Phillips Head Screw
16
415-5001
2 Union Nut
17
419-7241
Coupling
18
711-4010
2 Union Gasket
19
PSP1100
1 HP - 1-Speed Supreme Pump
PSP1150
1 1/2 HP - 1-Speed Supreme Pump
PSP1200
2 HP - 1-Speed Supreme Pump
PSP2100
1 HP - 2-Speed Supreme Pump
PSP2150
1 1/2 HP - 2-Speed Supreme Pump
PSP2200
2 HP - 2-Speed Supreme Pump
20
429-7221
Pin & Anchor Assembly
21
311-1520
Faceplate - Supreme Pump
22
805-0330
O-Ring
23
319-1510
Supreme Pump Trap Body
24
319-1530
Supreme Trap Basket
25
805-0439
O-Ring
26
511-1310
Trap Lid
27
319-1540
C-Clip Supreme Pump
28
711-4000
1 1/2" Union Gasket
29
WV001H
Gate Valve
20
19
DETAIL 1
DETAIL 2
DETAIL 4
11
11
18
14
14a
16
17
10
12
13
28
29
13
12
6
4
9
9a
15a
15a
6
6a
5
2
3
6a
5a
4b
1
4
7
8
1a
1b
1c
9
16
17
19
20
27
21
22
23
11
11
18
14
15
14a
15a (x 2)
24
25
26
28
29
13
12
10
12
13
DETAIL 5
15a
DETAIL 3
4a
4b