background image

8

 

 

                                                                                                                                                   

                                                                                                                                         

Installation

 - Drain Line Connection -

1. The drain line flow control assembly is pre-assembled for your convenience. Should you choose to hard 

    plumb the drain line, please remove the barb fitting. The flow control housing can be removed by remov

    ing the clip and pulling straight out on housing. 

Note:

 When re-installing the drain line flow control housing, be sure you hear and feel the O-Ring pop into

            place before inserting the clip.

2. Install 1/2” I.D. drain line tubing (not included) from hose barb to an open drain. A 4” gap between end of

    the drain line and the open drain is required to prevent waste water backflow. Keep the drain line as 

    short as possible. An overhead drain line can be used if necessary, but should discharge below the con

    trol valve. A syphon trap (taped loop) at the outlet of the drain line is advisable to keep the drain line full

    and assure correct flow during backwash. Elbows or other fittings must be kept at a bare minimum.

Note:

 Where the drain line is elevated above the control valve or exceeds 20 feet in length, 3/4” I.D. drain 

           line tubing should be used. 

-Brine Line and Overflow Connection-

Note: Your brine tank comes with two brine lines. Black is for outdoor installation. Opaque is for indoor installation.

Remove brass compression nut from the softener con-
trol valve.  Take brine tubing (packaged with brine tank) 
and slide the brass nut and plastic ferrule onto one end 
of the tubing.  Find the plastic tubing insert (taped to the 
brine well cap inside the brine tank) and insert it into the 
end of  the tubing. Next, insert the tubing into the control 
valve and tighten the nut. 

Inside the brine tank, remove the cap from the top of the brine 
well.  Feed the other end of the brine tubing through the hole 
in the side of the brine tank, and firmly insert it all the way into 
the push-lock elbow fitting inside the brine well.  When this 
tubing is fully inserted, the fitting will grab the tubing and hold 
it in place. 

BRINE LINE CONNECTION TO CONTROL VALVE

BRINE LINE CONNECTION TO BRINE TANK

Insert

Nut

Ferrule

Summary of Contents for HD33-3





























Reviews: