WaterSoft HD33-3 Installation & Operation Manual Download Page 2

Page: 2 / 28

www.watersoftinc.com

Online at

Register Your Product

Softener Specifications............................................................

Page 3

Softener Installation.................................................................

Page 5

Programming the Control Valve...............................................

Page 12

Master Programming...............................................................

Page 14

Utilizing Bluetooth...................................................................

Page 15

Control Valve Powerhead Assy. ISO III..................................

Page 18

Valve Body Assembly ISO III...................................................

Page 19

Bypass Assembly ISO III..........................................................

Page 21

Service Instructions.................................................................

Page 22

Troubleshooting........................................................................

Page 24

Error Codes..............................................................................

Page 26

Warranty Information..............................................................

Page 28

FCC Compliance Statement:

http://www.chandlersystemsinc.com/files/FCC_Compliance_Statement.pdf

Industry Canada Compliance Statement:

http://www.chandlersystemsinc.com/files/Industry_Canada_Compliance_Statement.pdf

One or more features of this product are covered by U.S. patents, visit

http://www.watersoftinc.com/patents.php

for more information.

Summary of Contents for HD33-3





























Search results

Summary of Contents for HD33-3

Reviews:

Related manuals for HD33-3

Brands by name

Popular brands

WaterSoft HD33-3, Installation & Operation Manual

Search results

Summary of Contents for HD33-3

Reviews:

Related manuals for HD33-3

Brands by name

Popular brands