background image

 

WL15

 Manual 

                                                      Page 4 – Revision:  4-15-22 

SAFETY ALERT SYMBOLS 

 

Read and follow all safety information carefully.  The signal words used in this manual are 
selected as shown below and based on an assessment of the degree of potential injury or 
damage (severe or minor) and the occurrence of injury (definitely occurs or has the potential to 
occur) when the warning is ignored: 

 

 DANGER!   

Indicates a situation which, when not avoided, results in death or severe injury.   

 

 WARNING!   

Indicates a situation which, when not avoided, has the potential to result in death or 
severe injury; and/or severe property damage.  

  

 

 CAUTION!   

Indicates a situation which, when not avoided, results or has the potential to result in 
minor injury; and/or minor property damage. 

 

 
 

SAFETY PRECAUTIONS 

 

 
Basic safety precautions should be followed, including the following: 

Ensure all Local, State, and Federal Laws and Codes including health and safety guidelines are 
met when installing 

Waterlogic

 Equipment.   Only qualified service technicians should attempt 

installation and service of 

Waterlogic

 Equipment.  Always read the entire operating instructions 

before using the appliance and save these instructions for future use. 

 

DANGER!  

This product can cause death or severe injury if incorrectly operated, installed or 

maintained. 

The installation, maintenance, sanitizing and any repair must be performed by 

qualified persons trained by Waterlogic International or their approved distributors only.  Do 
not remove any panel or cover to protect against electrical shock and exposure to UV 
radiation.   

 

DANGER! 

ELECTRICAL SHOCK HAZARD

.  

Always use a dedicated and properly grounded 

outlet.  Unit should be protected by ground-fault circuit interrupter (GFCI) or residual current 
device (RCD) having a rated residual operating current not exceeding 30mA.  Use only 
Waterlogic supplied power cord. Never use extension cords or power strips to connect unit. 
Do not use if the power supply cord is damaged. Always unplug from power supply prior to 
servicing. 

 

WARNING!

  

AUTHORIZED USE ONLY.  

This appliance is to be used for its intended purpose as 

described in this manual.  Untrained individuals who use this manual assume the risk of any 
resulting property damage or personal injury.  This appliance can’t be used by children and 
persons with reduced physical, sensory or mental capabilities or lack of experience.   

 

WARNING!

  

DO NOT OPERATE IF DAMAGED.

  Unplug and isolate water supply if abnormal 

conditions exist. Contact Waterlogic or authorized dealer for repair, service, and installation 
to avoid hazards.  

 

 

Summary of Contents for WL15-HCS










Reviews: