background image

I pg 09

Waterco Hydrochlor ST

GENERAL SAFETY RULES

 

1)  The equipment mentioned in this manual is specially designed for the sanitizing of 

water in swimming pools.

2)  It is designed to work with clean water at a temperature not exceeding 35°C (95°F). 
3)  The installation should be carried out in accordance to the safety instructions of 

swimming pools especially Standard HD 384.7.702 and the specific instructions for 
each facility.

4)  The rules enforced on accident prevention should be carefully followed.
5)  Any modification of the chlorinator requires the prior consent of the manufacturer.  

Original replacement parts and accessories authorized by the manufacturer ensure 
a high level of safety. The manufacturer accepts no liability for the damage and 
injuries caused by unauthorized replacement parts and accessories.

6)  During operation, some parts of the chlorinator are subject to dangerous electric voltage. 

Work may only be performed on the chlorinator or on the equipment connected to it 
after disconnecting them and the starting device from the mains power.

7)  The user should make sure that assembly and maintenance tasks are carried out 

by qualified authorized persons and that these persons have first carefully read 
the Service and Installation Instructions.

8)  The operating safety of the chlorinator is only guaranteed if the Installation and 

Service instructions are correctly followed.

9)  The limit values stated in the Technical Specifications should not be exceeded 

under any circumstance.

10)  In the event of defective operation or fault, contact the manufacturer’s Technical 

Support Department or its nearest Authorized Agent.

11)  If the supply cord is damaged, it must be replaced by the manufacturer or its 

service agent or a similarly qualified person.

12)  This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, 
unless they have been given supervision or instruction concerning use of the 
appliance by a person responsible for their safety.

13)  The appliance is not intended for use by young children. Young children should be 

supervised to ensure that they do not play with the appliance.

These chlorinators are approved and conformed to AS3136 Swimming Pool Equipment, 
as a prescribed article under Australian Registration.

These chlorinators conform to the Australian Electromagnetic Compatibility Standard 
marked by the C-tick.

WARRANTY

Two Years Warranty: 

Hydrochlor ST

2 years*

Electrolytic Salt Cell

2 years

Power pack

2 years

Commercial Installations

1 year

*Please refer to Waterco’s Warranty terms and conditions

Summary of Contents for HYDROCHLOR ST













Reviews: