WATANABE WSP-SHS Instruction Manual Download Page 1

   

 

6-16-19, JINGUMAE, SIBUYA-KU, TOKYO 150-0001, JAPAN 

Phone: +81-3-3400-6147    FAX: +81-3-3409-3156

 

 

1/3         

IM0346

-

03

 

Instruction 

Manual

 

WSP-SHS 
WSP-SLS

 

 
 
 
 
 
 

 

SIGNAL SELECTOR 

 
Thank  you  for  selecting  another  fine 

  product. 

Please  check  the  description  given  on  the  rating  label  of  this  unit  to 
make  sure  that  it  meets  your  specifications  and  be  sure  to  read  this 
instruction manual before using the product. 
This  manual  outlines  the  operation,  connection  and  adjustment 
procedures of this product. 
The unit has been manufactured and inspected according to our strict 
quality control standard. If you should find a defect including damage 
incurred  during  transportation,  contact  us  or  the  dealer  where  you 
purchased it immediately. 

○PACKAGE INCLUDES:   

Isolation converter.……………………1 

Base socket……………………………1 

 

*  For  details  of  models  and  specifications,  please  download  the 

product catalog from our website, and then check it. 

 

1

Overview

 

 
 
 

This  unit  is  a  plug-in  type  signal  converter  that  receives  two 
analog signals and automatically selects the higher or lower of 
them and outputs it. 
 

2

Functions and Features

 

 
 
 

Output zero span can be adjusted by front DIPSW 

Highly  reliable  design  that  is  not  affected  by  signal  source 

resistance and receiving resistance 

Realization of 5-year warranty by long-life design 

Compatible with worldwide power supply 

Compliant with CE marking 

 

3

Precautions

 

 
 
 

 

1)

 

Power supply: 

 

Check the rated voltage on the rating label, and use the product 

within the range of each of the following ratings. 

 

100 to 240VAC 

100 to 240VAC ±10% (50/60 Hz) approx. 5.5 VA 

 

24VDC 

24VDC ±10%, Approx. 100 mA 

 

100~120VDC 

100~120VDC ±10%, Approx. 25mA 

 
2)

 

Insulation resistance: 

Mutual between input - output - power supply 
terminal 
100MΩ or more/DC500V 
Non-isolated between 2 input terminals 

 
3)

 

Withstand voltage: 

Mutual between input - output - power supply   
terminal 
AC2000V 1 minute 

 

4) Handling 

· When removing or installing the main unit from the   

socket,  be  sure  to  shut  off  the  power  supply  and  input 
signal for safety. 

When touching the screws on the main unit or operating 
the  output  adjustment  switch,  touch  a  metal  object  to 
remove static electricity before doing so. 

5) Installation 

Please use indoors. 

When installing in a place with a lot of dust, metal   

powder, etc., store it in a dust-proof housing and   
take heat dissipation measures. 

Avoid vibrations and impacts as much as possible,   
as they may cause failure. 

Install in a place where the ambient temperature   

does not exceed the range of -5 to 55°C. 

Install in a place where the ambient humidity is 90% RH 

or less (non-freezing, non-condensing). 

Do not block the ventilation openings of the   
main unit. 

5) Wiring 

Do not wire the power supply line, input line, or   

output  line  near  noise  sources,  relay  drive  lines,  or 
high-frequency lines.   

Avoid bundling together lines on which noise is   
superimposed or storing them in the same duct. 

6) Others 

The unit can be operated immediately after turning   
on the power, but 30 minutes of energization is   
required to satisfy all performance requirements. 

 

4

Outline Dimensions

 

 
 
 

 

 

 

5

Circuit Diagram

 

 
 
 

 

 

 

6. Mounting

 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Close mounting is possible, but please leave a space of   
6.5mm to 7mm or more for heat dissipation. 
As shown in the figure above, a 6.5mm interval can be created   
with a 29.5mm pitch.

 

Analog input 

circuit 

Digital   

calculation 

circuit 

Analog input 

circuit 

Power 

circuit 

Output circuit 

Base socket 

Unit : mm 

2-M3 or M4 

Or 

φ

4.5 hole 

Reviews: