manualshive.com logo in svg

Wareforce UL30, Installation, Operation And Service Manual, Page: 12 / 72

Share
Download
Wareforce UL30 Installation, Operation And Service Manual Download Page 12

07610-004-37-37-P

7

Electrical and grounding conductors must comply with the applicable portions of the 
National Electric Code ANSI/NFPA 70 (latest edition) and/or other electrical codes.

The data plate is located at the left-front side of the dishmachine. Refer to the data 
plate for machine operating requirements, machine voltage, total amperage, and serial 
number. 

Remove the back panel and set aside. This will require removing the screw at the 

bottom of the back panel with a phillips screwdriver. Install 3/4” conduit into the pre-

punched holes in the back of the control box. Route power wires and connect to power 
block and grounding lug. Install the service wires (L1 and L2 for UH30-FND, L1 and 
N for UL30) to the appropriate terminals as they are marked on the terminal block. 

Install the grounding wire into the lug provided. It is recommended that “DE-OX” or 

another similar anti-oxidation agent be used on all power connections.

 

         

UH30-FND 

 

 

 

    UL30

Ensure the ON/OFF switch is in the OFF position and apply power to dishmachine. 
Check the incoming power at the terminal block and ensure it corresponds with the 

voltage listed on the data plate. If not, contact a qualified service agency to examine 
the problem. Do not run dishmachine if voltage is too high or too low. Shut-off the 

service breaker and advise all proper personnel of the location of the breaker and 
any problems. Replace the control box cover and tighten-down the screws.

This is a commercial dishmachine and reaches temperatures that can exceed 

those generated by a residential machine. Surrounding countertops, cabinets, flooring 
material, and subfloor material must be designed and/or selected with these higher 

temperatures in mind.

Any damage to surrounding area that is caused by heat and/or moisture to materials 
that are not recommended for higher temperatures will not be covered under warranty 
or by the manufacturer.

The thermostats on this dishmachine have been set at the factory. They should only 
be adjusted by an authorized service agent.

INSTRUCTIONS

INSTALLATION

ELECTRICAL POWER 

CONNECTIONS

Disconnect electrical 

power at the breaker or 

disconnect switch and 

tag-out in accordance with 

procedures and codes.

THERMOSTATS

SURROUNDING 

AREA

VOLTAGE CHECK

NOTICE

i

     L1     L2

GRND

     L1      N

GRND

Summary of Contents for UL30









































































Reviews:

No comments