W&H Lara RIL-117 Instructions For Use Manual Download Page 10 | Manualshive

Page: 10 / 138

background image

10

LARA | Instructions for use | RIL-1 ENG Rev04 | 28/02/2019 | © 2019 W&H Sterilization Srl

Safety information

TAMPERING

n

Do not remove the name plate or labels from the
sterilizer.

n

Repairs, maintenance or service must be carried
out by authorized service providers always using
genuine spare parts.

REQUIREMENTS

n

Use only the power cord set and accessories
provided by the manufacturer.

n

If the sterilizer is connected to a water supply
system, this must be fitted with a backflow
preventing device complying to IEC 61770.

Responsibility

USER RESPONSIBILITY

n

The user is responsible for the proper installation, the correct
use and maintenance of the sterilizer in accordance with these
Instructions for use.

n

The safety devices of the sterilizer are impaired when the
product itself is not installed, used and serviced in accordance
with these Instructions for use.

n

The Instructions for use updated to the latest version is always
available at www.wh.com.

n

Keep these Instructions for use for future reference.

MANUFACTURER RESPONSIBILITY

n

The manufacturer can only accept responsibility for the safety,
reliability and performance of the product when the product
itself is installed, used and serviced in accordance with the
Instructions for use.

n

Servicing by unauthorized persons invalidates all claims under
warranty and any other claims.

«
...
8
9
10
11
12
...
»

Summary of Contents for Lara RIL-117











































































































































Reviews:

No comments

Related manuals for Lara RIL-117

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands