Waltron AQUALERT Aqualyzer 3051 Instruction Manual Download Page 44 | Manualshive

Page: 44 / 70

Waltron AQUALERT Aqualyzer 3051 Instruction Manual Download Page 44

Operation

43

Waltron User Manual

3051 Hardness Analyzer

5.

When the analyzer has finished the grab sample analysis cycle, the concentration reading
will be displayed on the main screen. The result can also be found in the data logger.

6.

The analysis returns to standby mode and waits for another user command.

7.

When the user is finished with the grab sample analysis, make sure to reconnect the
sample tubiing to the fast loop resevoir.

8.

Turn on sample flow to the fast loop resevoir.

9.

Put the analyzer back into online operation mode by pressing the RUN Menu and
selecting START ON LINE.

6.7

EMERGENCY STOP

The analyzer has an emergency stop function that will stop the analyzer immediately during any
analysis cycle that it is performing.

1.

Press the RUN Menu.

2.

Select EMERGENCY STOP.



The analyzer will stop its current function and return to the main display screen.



The emergency stop fault alarm will be activated.

3.

To put the analyzer into standby mode after an emergency stop, press the RUN Menu.

4.

The menu will now show RESET in the posistion that emergency stop was listed
previously.

5.

Select RESET to deactivate the alarms and return the analyzer to the main display screen
in standby mode.

NOTE:

After initiating an emergency stop, there may be sample and
reagents remaining in the analyzer. It will be necessary to
flush the system before performing a new analysis cycle.

«
...
42
43
44
45
46
...
»

Summary of Contents for AQUALERT Aqualyzer 3051







































































Reviews:

No comments