manualshive.com logo in svg

Waltron AQUALERT Aqualyzer 3051, Instruction Manual, Page: 28 / 70

Share
Download
Waltron AQUALERT Aqualyzer 3051 Instruction Manual Download Page 28

 

 

 

 

 

 

 

Installation 

27 

Waltron User Manual 

3051 Hardness Analyzer 

3.6.2 

USER SIGNAL CONNECTIONS 

The analyzer provides an External Terminal Block on the outside of the Electronics Enclosure.  It 
allows the operator  to connect to an external device such as a sequencer or sampler, monitor the 
4-20mA ouputs and monitor alarm  relays.  The external terminal block can be configured from 
the SERVICE Screen.  
 
Table 3.1 below shows the terminal contact labels starting with pin 1 on the left. 
 

 

Figure 3.2: Electrical connections for user connections and power connections. 

 

Table 3.1: Terminal block pin locations. 

Pin Number 

Terminal Label 

Description 

1 

- Input 

NO contact from an External Device to tell 
the analyzer to take a measurement.  

2 

+ Input 

3 

- Signal 2 

4-20mA output for Sample 2 Measurement 

4 

+ Signal 2 

5 

- Signal 1 

4-20mA output for Sample 1 Measurement 

6 

+ Signal 1 

7 

COM ½ 

Common for Relay 1 and 2 

8 

OUT Relay 1 

Alarm Relay 1  NO Contacts 

9 

OUT Relay 2 

Alarm Relay 2 NO Contacts 

10 

OUT Relay 3 

Alarm Relay 3  NO Contacts 

11 

OUT Relay 4 

Alarm Relay 4 NO Contacts 

12 

COM 3/4 

Common for Relay 3 and 4 

 
 

Summary of Contents for AQUALERT Aqualyzer 3051







































































Reviews:

No comments