manualshive.com logo in svg

Waltron AQUALERT Aqualyzer 3051, Instruction Manual, Page: 16 / 70

Share
Download
Waltron AQUALERT Aqualyzer 3051 Instruction Manual Download Page 16

 

 

 

 

 

 

 

Introduction 

15 

Waltron User Manual 

3051 Hardness Analyzer 

2 

INTRODUCTION 

2.1 

ANALYZER DESCRIPTION 

This manual provides general information regarding the principle of operation, proper installation 
and operation of the Waltron 3051 Hardness Analyzer.  
 
The Waltron 3051 is an on-line analyzer for batch-wise analysis (sequence of sampling, analysis 
and result processing), using colorimetric method. The analyzer is assembled in an enclosure with 
lockable door. The LIQUIDS enclosure includes all the components involved in sample and 
reagents flows as well as their mixing and reaction stages (sampling pump, colorimetric reaction 
cell, reagents micropumps). The ELECTRICAL enclosure includes the main power supply, the 
controller PCB assembly and the touchscreen interface. 
 
 

 

Figure 2.1: Waltron 3051 Analyzer front view.            

Summary of Contents for AQUALERT Aqualyzer 3051







































































Reviews:

No comments