Wallenstein WXR700 Series Operator'S Manual Download Page 10

 Safety

WXR720/L, WXR740/L

Trailer Wood Splitter

Safety

10

2.8  Refueling Safety

• 

Engine fuel is highly flammable. Handle with care.

• 

Fill fuel tank outdoors.

• 

Stop the engine before refueling. Allow engine to cool for 
five minutes. Clean up spilled fuel before restarting engine. 

• 

Do not overfill the fuel tank.

• 

If fuel is spilled, wipe it away carefully and wait until the fuel 
has dried before starting the engine.

• 

Do not refuel the machine while 
smoking or when near open flame or 
sparks.

• 

After refueling, make sure that the fuel cap is secured to 
prevent spillage.

• 

Prevent fires by keeping machine clean of accumulated 
trash, grease, and debris.

2.9  Tire Safety

• 

Failure to follow proper procedures when mounting a tire on 
a wheel or rim can produce an explosion which may result 
in serious injury or death.

• 

Do not attempt to mount a tire unless you have the proper 
equipment and experience to do the job.

• 

Have a qualified tire dealer or repair service perform 
required tire maintenance.

• 

When replacing worn tires, make sure they meet the 
original tire specifications. Never install undersized tires.

2.10 Hydraulic System Safety

• 

Make sure that all the components in the hydraulic system 
are kept in good condition and are clean.

• 

Before applying pressure to the system, 
make sure all components are tight, and 
that lines, hoses and couplings are not 
damaged.

• 

Do not attempt any makeshift repairs to the hydraulic lines, 
fittings or hoses by using tapes, clamps or cements. The 
hydraulic system operates under extremely high pressure. 
Such repairs can fail suddenly and create a hazardous and 
unsafe condition.

• 

Wear proper hand and eye protection 
when searching for a high-pressure 
hydraulic leak. Use a piece of wood 
or cardboard as a backstop instead of 
hands to isolate and identify a leak.

• 

If injured by a concentrated high-pressure stream of 
hydraulic fluid, seek medical attention immediately. Serious 
infection or toxic reaction can develop from hydraulic fluid 
piercing the skin surface.

• 

Relieve pressure in the hydraulic system before working on 
it.

2.11 Engine Safety

 CAUTION!

Before starting the engine, review the safety, 

operating, and maintenance instructions in the 

engine manual.

W019

IMPORTANT!  In some regions, when an engine is used 
on any forest covered, brush covered, or grass covered 
unimproved land it is required by law to have a spark 
arrestor installed on the muffler. A spark arrestor traps 
exhaust particles that are expelled from the engine. It is the 
responsibility of the operator to comply with the local laws 
and regulations. To purchase a spark arrestor, contact your 
local Wallenstein dealer or distributor.

•  DO NOT

 operate engine in an enclosed area. Exhaust gases 

contain odorless and deadly carbon monoxide that can 
cause death by asphyxiation.

•  DO NOT

 place hands or feet near moving or rotating parts.

•  DO NOT

 store, spill, or use gasoline near an open flame, 

or devices such as a stove, furnace, or water heater which 
use a pilot light or devices which can create a spark.

•  DO NOT

 refuel indoors where area is not well ventilated. 

•  DO NOT

 refuel while engine is running. Allow engine to cool 

for five minutes before refueling. Store fuel in approved 
safety containers.

•  DO NOT

 remove fuel tank cap while engine is running.

•  DO NOT

 operate engine if gasoline is spilled. Move machine 

away from the spill and avoid engine ignition until gasoline 
has evaporated.

•  DO NOT

 smoke while filling fuel tank.

•  DO NOT

 choke carburetor to stop engine. Whenever 

possible, gradually reduce engine speed before stopping.

•  DO NOT

 run engine above rated speeds. This may result in 

injury.

Summary of Contents for WXR700 Series

















































Reviews: