background image

WX520 / WX520L / WX520T
Log Splitter

Specifications

35

11.2 Common Bolt Torque Values

Checking Bolt Torque

The tables shown give correct torque values for various 
bolts and capscrews. Tighten all bolts to the torque 
values specified in the table, unless indicated otherwise. 
Check tightness of bolts periodically. 

IMPORTANT!  If replacing hardware, use fasteners of 
the same grade.

IMPORTANT!  Torque figures indicated in the table are 
for non-greased or non-oiled threads. Do not grease or 
oil threads unless indicated otherwise. When using a 
thread locker, increase torque values by 5%.

 NOTE:

Bolt grades are identified by their head 
markings.

Imperial Bolt Torque Specifi cations

Bolt 

Diameter

Torque Value

SAE Gr� 2

SAE Gr� 5

SAE Gr� 8

lbf•ft

N•m

lbf•ft

N•m

lbf•ft

N•m

1/4"

6

8

9

12

12

17

5/16"

10

13

19

25

27

36

3/8"

20

27

33

45

45

63

7/16"

30

41

53

72

75

100

1/2"

45

61

80

110

115

155

9/16"

60

95

115

155

165

220

5/8"

95

128

160

215

220

305

3/4"

165

225

290

390

400

540

7/8"

170

230

420

570

650

880

1"

225

345

630

850

970

1320

Metric Bolt Torque Specifi cations

Bolt 

Diameter

Torque Value

Gr� 8�8

Gr� 10�9

lbf•ft

N•m

lbf•ft

N•m

M3

0�4

0�5

1�3

1�8

M4

2�2

3

3�3

4�5

M6

7

10

11

15

M8

18

25

26

35

M10

37

50

52

70

M12

66

90

92

125

M14

83

112

116

158

M16

166

225

229

310

M20

321

435

450

610

M30

1,103

1 495

1,550

2 100

Summary of Contents for WX520









































Reviews: