manualshive.com logo in svg

Wallenstein WP245, Operator'S Manual

Share
Download
Wallenstein WP245 Operator'S Manual Download Page 11

2.8  Sign-Off Form

Wallenstein follows the general Safety Standards specified by 
the American Society of Agricultural and Biological Engineers 
(ASABE). Anyone who will be using and/or maintaining the 
Wood Processor must read and clearly understand ALL Safety, 
Usage and Maintenance information presented in this manual.

Do not use or allow anyone else to use this Wood Processor 
until such information has been reviewed. Annually review this 
information before the season start-up.

Make these periodic reviews of SAFETY and OPERATION 
a standard practice for all your equipment. We feel that an 
untrained operator is unqualified to use this machine.

A sign-off sheet is provided to record all personnel who will 
be working with the equipment have read and understand the 
information in the Operator's Manual and have been instructed in 
the operation of the equipment.

Sign-off Form

Date

Owner

Employee

 Safety

WP245 / WP275
3-Point Hitch Firewood Processor

Safety

11

Summary of Contents for WP245





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands