WAGO TEchDocs 765-4501/0100-0000 Manual Download Page 105

Page: 105 / 136

765-4501/0100-0000

Commissioning

Product manual | Version: 1.1.0

105

8PORT IOL-A FLD EI DC 24V 2.0A

The light sensor registers this sequence. If the sequence is recognized as correct, the
Bluetooth

interface is enabled, and the product attempts to establish a Bluetooth

connection to the smartphone or tablet.

Starting a Bluetooth

Firmware Update

Proceed as follows to start a Bluetooth

firmware update:

1. Click

Update request

A dialog appears for selecting the Bluetooth

firmware file.

2. Select the firmware file.

The Bluetooth

firmware update starts.

Performing a Reset

Proceed as follows to reset the Bluetooth

firmware:

•

Click

Reset

The Bluetooth

firmware is reverted and restarts.

Switching the Bluetooth

Interface Wireless Transmitter on/off

To switch the Bluetooth

interface wireless transmitter on:

•

Slide the

Bluetooth radio

switch to the right

The Bluetooth

interface wireless transmitter switches on.

To switch the Bluetooth

interface wireless transmitter off, slide the

Bluetooth radio

switch to the left.

Switching LED Forcing on/off

Proceed as follows to switch LED forcing (externally controlled LED mode) on:

•

Slide the

LED forcing

switch to the right.

LED forcing switches on. The LED on the Bluetooth

interface can now be externally

controlled.

To switch LED forcing off, slide the

LED forcing

switch to the left.

10.3.1.4.8 Logging Users on and off and Managing Them

Logging Users on

Proceed as follows to log users on:

1. From the Webserver main menu (left), select the

Sign in

menu item.

The input screen for username and password appears:

Summary of Contents for TEchDocs 765-4501/0100-0000









































































































































Search results

Summary of Contents for TEchDocs 765-4501/0100-0000

Reviews:

Related manuals for TEchDocs 765-4501/0100-0000

Brands by name

Popular brands

WAGO TEchDocs 765-4501/0100-0000, Manual

Search results

Summary of Contents for TEchDocs 765-4501/0100-0000

Reviews:

Related manuals for TEchDocs 765-4501/0100-0000

Brands by name

Popular brands