manualshive.com logo in svg

WAGO ETHERNET Accessories 852 852-0111, Mounting, Installation And Handling Manual

Share
Download
WAGO ETHERNET Accessories 852 852-0111 Mounting, Installation And Handling Manual Download Page 25

WAGO ETHERNET Accessories 852 

List of Figures 

25 

852-0111 5 Port 100BASE-TX Industrial ECO Switch 

 

 

 

Manual 

 

Version 1.2.0, valid from FW/HW Version 01/06 

4.4.5 

Environmental Conditions 

Table 12: Technical data - environmental conditions 

Surrounding air temperature, operation 

-40 °C ... +70 °C 

Surrounding air temperature, operation, DNV 
GL (Temperature class D) 

-25 °C ... +70 °C 

Surrounding air temperature, operation, UL 

-40 °C ... +60 °C 

Surrounding air temperature, storage 

-40 °C ... +80 °C 

Relative humidity (without condensation) 

95 % 

Vibration resistance 

Acc. to IEC 60068-2-6 

Shock resistance 

Acc. to IEC 60068-2-27 

EMC-1 immunity to interference 

Acc. to EN 61000-6-2 

EMC-1 Emission of interference 

Acc. to EN 61000-6-4 

Standard Compass Safe Distance 0.3 
Degree deflection 

1000 mm 

Steering, Standby, Emergency Compass 
Safe Distance 1.0 Degree deflection 

650 mm 

 

 

 

 

Summary of Contents for ETHERNET Accessories 852 852-0111







































Reviews:

No comments

Brands by name

Popular brands

Load more brands