WAGO 852-1305 Manual Download Page 291

Page: 291 / 314

WAGO-ETHERNET-Zubehör 852

Appendix 291

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.6.2 Auto Provision

Table 155: CLI “Auto Provision” Configuration

Node

Command

Description

auto-provision show

This command displays the current configurations

for the “Auto Provision”.

auto-provision active (enable | disable)

This command enables / disables the “Auto

Provision” function.

auto-provision server-address IPADDR

This command sets the IP address of the server for

the “Auto Provision”.

auto-provision protocol (tftp | http | ftp)

The command configures the update protocol.

auto-provision FTP-user username

STRING password

STRING

The command configures the username and

password for the FTP server.

auto-provision folder STRING

The command sets the folder for the “Auto

Provision” server.

auto-provision version <0-65535>

The command configures the version for “Auto

Provision” on the switch.

auto-provision no folder

The command resets the folder to the default setting.

auto-provision no FTP-user

The command resets the username and password to

default setting.

10.3.6.3 Mail Alarm

Table 156: CLI “Mail Alarm” Configuration

Node

Command

Description

enable

show mail-alarm

This command displays the “Mail Alarm”

configurations.

configure

mail-alarm (disable |

enable)

This command disables / enables the “Mail Alarm”

function.

configure

mail-alarm mail-from

This command configures the e-mail sender.

configure

mail-alarm mail-to

This command configures the e-mail receiver.

configure

mail-alarm server-ip

IPADDR server-port

VALUE

This command configures IP address and TCP port

for the mail server.

configure

mail-alarm server-ip

IPADDR server-port

Default

This command configures the IP address of the mail

server and sets its TCP port to 25.

configure

mail-alarm trap-event

(reboot | link-change |

config. | firmware | login |

port-blocked)

(disable|enable)

This command disables / enables mail trap events.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands