WAGO 852-1305 Manual Download Page 286

Page: 286 / 314

286 Appendix

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.4.7 802.1x

Table 147: CLI “802.1x” Configuration

Node

Command

Description

enable

show dot1x

This command displays the current 802.1x

configurations.

enable

show dot1x username

This command displays the current user accounts for

local authentication.

enable

show dot1x accounting-

record

This command displays the local accounting records.

configure

dot1x authentication

(disable | enable)

This command enables / disables 802.1x

authentication on the switch.

configure

dot1x authentic-method

(local | radius)

This command configures the 802.1x authentication

method.

configure

no dot1x authentic-

method

This command sets the 802.1x authentication method

to the default setting.

configure

dot1x radius primary-

server-ip <IP> port

PORTID

This command configures the primary radius server.

configure

dot1x radius primary-

server-ip <IP> port

PORTID key KEY

This command configures the primary radius server.

configure

dot1x radius secondary-

server-ip <IP> port

PORTID

This command configures the secondary radius

server.

configure

dot1x radius secondary-

server-ip <IP> port

PORTID key KEY

This command configures the secondary radius

server.

configure

no dot1x radius

secondary-server-ip

This command deletes the secondary radius server.

configure

dot1x username

<STRING> passwd

This command configures the user account for local

authentication.

configure

no dot1x username

This command deletes the user account for local

authentication.

configure

dot1x accounting

(disable|enable)

This command enables / disables the local .1x

accounting records.

configure

dot1x guest-vlan

VLANID

This command configures the guest VLAN.

configure

no dot1x guest-vlan

This command deletes the guest VLAN.

interface

dot1x admin-control-

direction (both|in)

This command configures the control direction for

blocking packets.

interface

dot1x default

This command resets the port configuration to the

default settings.

interface

dot1x max-req <1-10>

This command sets the “Max-req Times” of a port.

(1 to 10).

interface

dot1x port-control (auto |

force-authorized | force-

unauthorized)

This command configures the port control mode on

the port.

interface

dot1x authentication

(disable | enable)

This command enables / disables 802.1x

authentication on the port.

interface

dot1x reauthentication

(disable | enable)

This command enables / disables the authentication

interval on the port.

interface

dot1x timeout quiet-period This command configures the “Quiet Period” value

on the port.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands