WAGO 852-1305 Manual Download Page 270

Page: 270 / 314

270 Appendix

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.3.7 Multicast Address

Table 128: CLI “Multicast Address” Configuration

Node

Command

Description

enable

show mac-address-table

multicast

This command displays the current static/dynamic

multicast address entries.

configure

mac-address-table

multicast MACADDR

vlan VLAN_ID ports

PORTLIST

This command configures a static multicast entry.

configure

no mac-address-table

multicast MACADDR

This command deletes a static multicast entry from

the address table.

10.3.3.8 VLAN

10.3.3.8.1 Port Isolation

Table 129: CLI “Port Isolation” Configuration

Node

Command

Description

enable

show port-isolation

This command displays the current “Port Isolation”

configurations.

“V” indicates that the port's packets can be sent to

that port.

“-” indicates that the port's packets cannot be sent to

that port.

interface

port-isolation ports

PORTLISTS

This command configures a port or port range to

forward data packets from a specific port.

interface

no port-isolation

This command configures all ports to forward data

packets from a specific port.

Example

L2SWITCH(config)

#interface 1/0/2

L2SWITCH(config-if)

#port-isolation ports 3-10

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands